Frigidaire FGHG2368TF Installation Manual

Browse online or download Installation Manual for Unknown Frigidaire FGHG2368TF. Frigidaire FGHG2368TF Installation Instructions User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 3
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
DO NOT REMOVE this label until the refrigerator has been leveled.
Please follow all instructions for leveling your refrigerator.
P/N: A05972302
2
1
7
Doors
Handles are secure and tight
Door seals completely to cabinet on all sides
Fresh food doors are level
Leveling
Refrigerator is level, side to side and tilted
¼ inch (6 mm) front to back
Toe grille is properly attached to refrigerator
Cabinet is sitting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
Installation Check List
Preparing For Installation
Be sure to coordinate site preparation and installation
with your kitchen contractor.
Include these minimum guidelines in your site preparation:
Choose a place near a grounded electrical outlet.
Do not use an extension cord or an adapter plug.
Avoid direct sunlight and close proximity to a range,
dishwasher or other heat source.
Floor should be level and able to support a fully
loaded refrigerator.
The refrigerator’s Ice Dispenser
requires water supply access.
Plan for easy access to counter tops
when removing food.
For complete access to drawers and
freezer baskets, doors must be able to
fully open.
Load refrigerator from side of cabinet only.
Do not run retaining straps over handles nor overtighten straps.
Never use refrigerator handles to move the refrigerator.
Allow the following clearances for ease of installation, proper air
circulation, and plumbing and electrical connections: Sides & Top:
3
/
8
inch / Rear: 1 inch
Level Refrigerator
6
Frigidaire uses packing foam and tape to secure the internal parts of your refrigerator for
shipping. Once the refrigerator is in position, you can remove this material.
What’s Next?
Congratulations! You are ready to begin enjoying your new Frigidaire refrigerator.
For important safety instructions and to learn how to operate your refrigerator, please read
the entire Use & Care Guide.
You may want to start with the “Normal Operating Sights & Sounds” section of the Guide to
learn what to expect during typical operation.
Please register your product. You can register online at www.frigidaire.com or you can
simply send in the Registration Card.
Guidelines for nal positioning of your refrigerator
Allfourcornersofthecabinetmustrestrmlyontheoor.
The sides should tilt ¼ inch (6 mm) from front to
back (to ensure that doors close and seal properly).
Doors should align with each other and be level.
Most of these conditions can be met by raising or
lowering the adjustable front rollers.
To level the cabinet using the front rollers:
1 You can raise or lower each door. Use a
3
/
8
inch socket
wrench to turn the adjustment screws (1 per side).
To raise: turn adjustment screw clockwise.
To lower: turn adjustment screw counterclockwise.
2 Ensure both doors are bind-free with their seals
touching the cabinet on all four sides and that cabinet
is stable.
3 After unit is leveled, lower anti-tip leg until it contacts
theoor.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power
source.
2. Place end of water supply line into sink or
bucket.TurnONwatersupplyandushsupply
line until water is clear. Turn OFF water supply
at shutoff valve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve) onto
water supply line. Push water supply line into
water valve inlet as far as it will go (¼ inch).
Slideferrule(sleeve)intovalveinletandnger
tighten nut onto valve. Tighten another half
turn with a wrench; DO NOT overtighten. See
Figure 1.
Ifyouusebraided,exiblestainlesssteel
tubing - The nut is already assembled on the
tubing.Slidenutontovalveinletandnger
tighten nut onto valve. Tighten another half
turn with a wrench; DO NOT overtighten. See
Figure 2.
5. With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel of
refrigerator as shown.
6. Coil excess water supply line (copper tubing
only), about 2½ turns, behind refrigerator as
shown and arrange coils so they do not vibrate
or wear against any other surface.
7. Turn ON water supply at shutoff valve and
tighten any connections that leak.
8. Reconnect refrigerator to electrical power source.
9. To turn ice maker on, lower wire signal arm
(freezer ice maker) or set the ice maker’s On/
Off power switch to the “ON” position (fresh
food ice maker).
Before Installing The Water Supply Line, You Will Need:
• BasicTools:adjustablewrench,at-bladescrewdriver,and
Phillips
TM
screwdriver
Access to a household cold water line with water pressure
between 30 and 100 psi.
A water supply line made of ¼ inch (6 mm) OD, copper
orbraided,exiblestainlesssteeltubing.Todetermine
the length of tubing needed, measure the distance from
the ice maker inlet valve at the back of the refrigerator to
your cold water pipe. Then add approximately 7 feet, so
the refrigerator can be moved out for cleaning.
A shutoff valve to connect the water supply line to your
household water system. DO NOT use a self-piercing type
shutoff valve.
A compression nut and ferrule (sleeve) for connecting a copper water supply line to the
ice maker inlet valve.
*Please refer to your Use & Care Guide for more details.
Connect Water Supply
Ice Maker
House water supply connected to
refrigerator
No water leaks present at all connections
Ice Maker is turned ON.
Final Checks
Shipping material removed
Fresh Food and Freezer temperatures set
3
Raise
Lower
Anti-tip
Leg
Door
Door
If you are not satised with the installation of your refrigerator, please contact the store where you purchased it or call 1-800-944-9044 for assistance.
Removing & Replacing Freezer Drawer
4
Remove Internal Shipping Materials
Installation Instructions* for French Door Bottom Freezer/Refrigerator
WARNING
To avoid electric shock, which can cause death or severe personal
injury, do not connect your refrigerator to an electrical power source
until you have completed Step 2 of these instructions.
CAUTION
Shifting the refrigerator from side to side
may damage flooring.
Do not block the toe grille on the lower
front of your refrigerator. Sufficient air cir-
culation is essential for proper operation.
IMPORTANT
If you are installing your refrigerator
without connecting it to a water
supply, make sure the ice maker’s
power switch is turned Off (see the
Use & Care Guide for more details).
NOTE
If you need to remove the doors to get your refrigerator into the house, please refer to “Removing Doors”
in the Use & Care Guide. These installation instructions are provided only as a possible customer option.
Frigidaire recommends that you use a service or kitchen contracting professional to install your refrigerator.
NOTE
Check with your local building authority for
recommendations on water lines and associated
materials prior to installing your new refrigerator.
Depending on your local/state building codes,
Frigidaire recommends for homes with existing
valves its Smart Choice 6 ft. Stainless Steel
Refrigerator Water Line Kit 5304490728,
and for homes without an existing valve,
Frigidaire recommends its Smart Choice 20 ft.
Copper Refrigerator Water Line Installation Kit
5304490717 (with a with self-tapping saddle
valve). Please refer to www.frigidaire.com for
more information.
CAUTION
Room temperatures
below 55°F (13°C)
or above 110°F
(43°C) will impair
cooling ability of
your refrigerator’s
compressor.
NOTE
Please call 1-800-944-9044 if you
need assistance with this installation.
WARNING
To avoid electric shock,
which can cause death
or severe personal
injury, disconnect the
refrigerator from elec-
trical power before con-
necting a water supply
line to the refrigerator.
CAUTION
To Avoid Property Damage:
Copper or Stainless Steel braided, flexible tubing is recommended for
the water supply line. Water supply tubing made of ¼ inch (6 mm)
plastic is not recommended to be used. Plastic tubing greatly increases
the potential for water leaks, and the manufacturer will not be respon-
sible for any damage if plastic tubing is used for the supply line.
Do not reuse compression fitting or use thread seal tape.
DO NOT install water supply tubing in areas where temperatures fall
below freezing.
Chemicals from a malfunctioning softener can damage the ice maker.
If the ice maker is connected to soft water, ensure that the softener
is maintained and working properly.
®
Adjusting Doors (if necessary)
5
Removing Freezer Drawer
1. Remove 4 hex head drawer screws.
2. Lift up drawer to remove.
Remove
Hex Head
Drawer Screw
DO NOT
Remove
Other
Screws
DO NOT
Loosen
or
Remove
These 3
Hex
Screws
Replacing Freezer Drawer
1. Lower drawer back into place.
2. Replace 4 hex head drawer screws
and tighten.
Raise
To make nal door height adjustments:
1. Open freezer drawer to make lower hinge visible.
2. Insert 6 mm Allen wrench into the shaft of
the lower hinge.
3. Adjust the height by turning clockwise or
counterclockwise. Turning clockwise will
lower the door. Turning counterclockwise will
raise the door. Default setting is to the lowest
height when you receive your appliance.
Steel
Clamp
Braided
Flexible
Stainless
Steel
Water Line
Water Valve
Bracket
Valve Inlet
Water Valve
6 ft (1.8 Meters) Braided flexible
stainless steel water line from
household water supply.
Plastic Water Tubing
to Ice Maker
Fill Tube
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Plastic Water
Tubing to Ice
Maker Fill
Tube
Steel
Clamp
Brass
Compression
Nut
Ferrule
(Sleeve)
Copper
water line
Water Valve
Bracket
Valve Inlet
Water Valve
Copper water line
from household
water supply
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure 1
Figure 2
Page view 0
1 2 3

Summary of Contents

Page 1 - Anti-tip

DO NOT REMOVE this label until the refrigerator has been leveled. Please follow all instructions for leveling your refrigerator.P/N: A05972302217Doors

Page 2

NO QUITE esta etiqueta hasta que se haya nivelado el refrigerador. Siga las instrucciones para nivelar su refrigerador.P/N: A059723022 17Puertas□ Las

Page 3 - ATTENTION

NE RETIREZ PAS cette étiquette avant que le réfrigérateur ait été mis de niveau. Veuillez suivre toutes les instructions concernant la mise à niveau

Comments to this Manuals

No comments