Frigidaire FFGS3025PB User Manual download pdf (Page 3)

Specifications

subject to change.

30" Gas Slide-In Range

Baseline

USA

•

10200 David Taylor Drive

•

Charlotte, NC 28262

•

1-800-FRIGIDAIRE

•

frigidaire.com

CANADA

•

5855 Terry Fox Way

•

Mississauga, ON L5V 3E4

•

1-800-265-8352

•

frigidaire.ca

Slide-In Ranges

FFGS3025P S / W / B 30" Gas

Slide-In Range Specifications

•

Product Shipping Weight (approx.) – 220 Lbs.

•

Voltage Rating – 120V / 60 Hz / 15 Amps

•

Connected Load (kW Rating) @ 120 Volts = 0.7 kW

(For use on adequately wired 120V, dedicated circuit having 2-wire

service with a separate ground wire. Appliance must be grounded

for safe operation.)

•

Amps @ 120V = 15 Amps

•

Always consult local and national electric and gas codes.

•

Make sure wall coverings around range can withstand heat generated

by range.

•

Linoleum or any other synthetic floor covering located beneath range,

must be capable of withstanding minimum heat of 90° F above room

temperature without shrinking, warping or discoloring. Insulating pad

or 1/4"-thick plywood required between range and a carpeted floor.

•

Do not obstruct flow of combustion air at oven vent nor around base

or beneath lower front panel of range. Range requires fresh air for

proper burner combustion.

•

Range ships with 3/4" factory regulator.

•

LP Gas Conversion Kit supplied.

•

Gas supply line can enter cabinet through back wall or floor.

Recommended position for gas supply line is located 7" from left

cabinet wall and 2" from floor. Electrical outlet can be located

anywhere on the back wall 2" from either side wall and 12" from floor.

Supply line must be equipped with approved manual shutoff valve,

accessibly located in same room as range.

•

Countertop MUST be level in all directions and adjustable range

height at least 1/16" greater than tallest cabinet height, to ensure

metal rangetop flange will fit properly on countertop edge.

•

When installing optional Backguard Kit, cutout depth of 21-3/4"

minimum / 22-1/8" maximum needs increased to 24".

•

Overhead cabinetry should not exceed a 13" maximum depth.

•

Absolute minimum horizontal distance between overhead cabinets

installed to either side of appliance must be no less than maximum

width of appliance.

•

Allow 24" minimum clearance between rangetop and bottom of cabinet

when bottom of wood or metal cabinet is protected by not less than 1/4"

flame-retardant millboard covered with not less than No. 28 MSG sheet

steel, 0.015" stainless steel, 0.024" aluminum or 0.020" copper. Allow 30"

minimum clearance when cabinet is unprotected.

•

Allow 5" minimum clearance from edge of rangetop to nearest

combustible wall on either side of unit.

•

To reduce risk of fire when using overhead cabinetry, install range

hood that projects horizontally a recommended minimum of 5" beyond

bottom of cabinets.

Countertop Preparation

Rangetop’s side flanges overlap countertop cutout edges – for detailed

preparation instructions, refer to product installation guide on the web.

•

Flat Square-Finish Countertops – require no preparation since

rangetop’s flange lays directly on countertop edge.

•

Formed Front-Edged Countertops – require front molded edge to

be shaved flat 3/4" from each front corner of opening.

•

Tile Countertops – may need trim cut back 3/4" from each front corner

of opening and /or rounded edge flattened.

•

For existing cutout width greater than 30-1/16" reduce the 3/4" overlap

dimension; for cutout width of 29", replace actual side

trim panels with smaller side trim panels, available with optional

Side Trim Kit (refer to detailed kit installation instructions).

Note: For planning purposes only. Refer to Product Installation Guide

on the web at frigidaire.com for detailed instructions.

Optional Accessories

•

Rear Filler Kit: Stainless Steel – (PN # 901193-901S),

White – (PN # 901193-9011), Black – (PN # 901193-9010).

•

Side Panel Kit: Stainless Steel – (PN # 903074-901S),

White – (PN # 903074-9011), Black – (PN # 903074-9010).

•

Backguard Kit: Stainless Steel – (PN # 903046-901S),

White – (PN # 903046-9011), Black – (PN # 903046-9010).

•

Side Trim Kit: Stainless Steel – (PN # 903075-901S),

White – (PN # 903075-9011), Black – (PN # 903075-9010).

1 2 3 4 5 6 7

Comments to this Manuals

No comments

Frigidaire FFGS3025PB User Manual Page 3

Comments to this Manuals

Related products and manuals for Kitchen Frigidaire FFGS3025PB