Frigidaire FPHS2699PF User Manual download pdf (Page 1)

SERVICE DATA SHEET

242288300

ICE & WATER - AUTOMATIC DEFROST

SIDE BY SIDE - R134a

IMPORTANT SAFETY NOTE

The information provided herein is designed to assist qualiﬁed repair personnel only. Untrained persons should not attempt to make

repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance.

IMPORTANT

If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured.

CAUTION

All electrical parts and wiring must be shielded from torch ﬂame. DO NOT allow torch to touch insulation; it will char at

200°F and ﬂash ignite (burn) at 500°F. Excessive heat will distort the plastic liner.

IMPORTANT: PLEASE RETURN THIS SHEET TO ITS ORIGINAL LOCATION

Diagnostic Mode

Activate:

Press ^ and V temperature pads for up to 10 sec. simultaneously.

Press + to advance through tests.

Deactivate:

Press + for up to 10 sec. Diagnostic Mode will automatically deactivate after 5 min. of inactivity.

Note: Silence alarm.

• Tests marked with “*” may not be applicable to this unit and will not be displayed in Diagnostic Mode.

• Tests displayed in diagnostic mode but not described below are for internal purposes only; advance through.

• View UI display for “on,” “off,” “CL,” “OP,” “SH,” “LO,” “HI” or numerical results of tests.

• Listen for operating sounds; feel for heat or air ow as appropriate to determine results of tests.

Test To activate test: Passing result

-- First Screen -- All LED lights on UI illuminated

-- Second Screen -- All segments on UI temperature displays illuminated

-- Third Screen -- Blank UI display, no lights illuminated, no shadowing; “-” and “+”

blinking on FF display side to show location.

28 Dispenser Paddle Press disp. paddle “on” on UI when depressed; “off” when released

1* Standard Compressor

and Condenser Fan

Press set Compressor and Condenser Fan running when “on”; stopped when “off”

2 Defrost Heater Press set Defrost limit switch must be closed; verify “CL” in test 26.

Feel for heat from defrost heater when “on”.

If “OP” in test 26, heater will not activate.

3 FF Light Press set With FF door open, FF lights on when “on”; off when “off”

8 Water Valve

(Dispenser)

Press set Be prepared to collect water at dispenser.

Water dispenses when “on”; stops when “off”

9 FZ Light Press set With FZ door open, FZ lights on when “on”, off when “off”

10 Auger Motor Press set FZ door must be closed.

Motor running when “on”; motor stopped when “off”

11 Cube/Crush

Solenoid

Press set

Do not leave solenoid in activated state.

Solenoid activated when “on”; deactivated when “off”

41* Perfect Temp Drawer

(PTD)

Press set PTD UI illuminated when “on”, off when “off”

12* VCC Condenser Fan Press set Fan running when “on”; stopped when “off”

38* VCC Compressor Press set Compressor running when “on”; stopped when “off”

15 Evaporator Fan Press set Fan running for minimum of 10 sec. when “LO” or “HI”; stopped when

“off”. Feedback failure if fan starts but runs less than 10 sec. Listen for

speed change from “LO” to “HI”.

22 Damper Press set With inspection mirror, observe damper open when “OP”; closed when “CL”

23 FF Door Open/close FF door “CL” on UI when door closed; “OP” when open

24 FZ Door Open/close FZ door “CL” on UI when door closed; “OP” when open

26 Defrost Limit Switch Activates automatically “CL” on UI when closed; “OP” when open

36 Ice Chute Door Depress ice chute door

or press set

“OP” on UI when manually opened; “CL” when closed. Or, using “set”,

“OP” on UI when solenoid activated, “CL” when deactivated

29 FF Thermistor

Mid-level

Activates automatically UI shows temperature sensed by FF thermistor; pass if within 10°F of

temperature measured with gauge at mid-level FF thermistor location.

“OP-” if open; “SH-” if short

30 FZ Thermistor Activates automatically UI shows temperature sensed by FZ thermistor; pass if within 10°F of temperature

measured with gage at FZ thermistor location.

“OP” if open; “SH” if short

33 Ambient Thermistor

@ Main Board

Activates automatically UI shows temperature sensed at main board; pass if within +20°F/-10°F

of temperature measured with gauge at main board location.

“OP” if open; “SH” if short

35 FF Thermistor

Upper-Level

Activates automatically UI shows temperature sensed by upper level FF thermistor; pass if within

10°F of temperature measured with gauge at upper-level FF thermistor

location. “OP¯” if open; “SH¯” if short

34 Ambient Thermistor

@ UI

Activates automatically UI shows temperature sensed at UI; pass if within +20°F/-10°F of tem-

perature measured with gauge at UI location. “OP” if open; “SH” if short

0- Firmware

Parameters

Press set Displays digit sequence; record

2- Main Board

Firmware

Press set Displays digit sequence; record

4- UI Firmware Press set Displays digit sequence; record

Variable Capacity Compressor (VCC) Diagnostics (select models)

If test 38 fails, diagnose as follows:

Replace Inverter

→ Check at the connector

from main control into

the inverter (typically

BLK and RED wires)

Is Inverter receiving

10-15 VAC

and 1-5 VDC from

Main Control?

→ Check at Main Control

Board

(BLK/WHT and RED/BLK wires)

Is Main Control

sending 10-15 VAC

and 1-5 VDC to

Inverter?

→ Check at the connector from

the service cord into the

inverter (typically PUR and

WHT wires.)

Is Inverter receiving 115

VAC from power supply?

yes

• Check voltage supply.

• Check and repair

service cord wiring

and connections.

Identify and repair

damaged wires or poor

connections between

Main Control and

Inverter

yes

→ Remove inverter box

from the compressor

and check resistance

across compressor

winding pairs as shown.

Is resistance across

all winding pairs

equal?

yes

Replace Compressor

→ Check connections

from Inverter to

Compressor

Are connections

from Inverter to

Compressor intact?

yes

Identify and repair

damaged wires or poor

connections between

Inverter and Compressor.

VCC Resistance Check

Check resistance between terminals

1 and 2, 2 and 3, 3 and 1.

If all resistances are equal,

compressor is operative.

Replace Main Control

PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT

0° F FREEZER & 37° F FRESH FOOD (2500 ++ V5)

Type A with Run/

Start Capacitor

65°F (18°C) Ambient 90°F (32°C) Ambient

Variable Speed Standard Variable Speed Standard

Operating Time 74 to 84% 32 to 40% 100% 55 to 65%

Freezer

Temperature

-2° to 2° F

-19° to -17° C

0° to 4° F

-18° to -16° C

-1° to 3° F

-18° to -16° C

-1° to 3° F

-18° to -16° C

Refrigerator

Temperature

34° to 39° F

1° to 4° C

34° to 39° F

1° to 4° C

34° to 39° F

1° to 4° C

34° to 39° F

1° to 4° C

Low Side Pressure

(cut-in)

5 to 12 psig

43 to 83 kPa

5 to 12 psig

43 to 83 kPa

N/A

5 to 12 psig

43 to 83 kPa

Low Side Pressure

(cut-out)

-2 to 2 psig

-14 to 14 kPa

-2 to 2 psig

-14 to 14 kPa

-2 to 2 psig

-14 to 14 kPa

-2 to 2 psig

-14 to 14 kPa

High Side

Pressure (last

cycle)

90 to 105 psig

621 to 724 kPa

90 to 115 psig

621 to 793 kPa

120 to 135 psig

827 to 931 kPa

130 to 155 psig

896 to 1069 kPa

Wattage (last

cycle)

50 to 60 90 to 130 60 to 70 100 to 140

Amps (running) 0.5 to 0.9 0.7 to 1.1 0.6 to 1.0 0.8 to 1.2

Base Voltage 115 vac (127 vac max)

DEFROST SPECIFICATIONS

Cabinet Size

Thermostat Heater

Cut-in Cut-out Watts Ohms

23’ CD, 26’ 25° F (-4° C) 47° F (8° C) 450 30

Electronic Timer - (ADC) Defrost 24 minutes every 6-96 hours of compressor run time.

CONDENSER FAN MOTOR

Watts RPM Amps

3.1 1100 CW Opposite Shaft 0.03 Running

OUT 1A

OUT 2A

OUT 1B

ERF-2500++ V5

REFRIGERATOR

CONTROL

NTC 1 - FF

NTC 2 - FF

NTC - FZ

DEFROST HEATER

DEFROST THERM.

NEUTRAL

CONTROL

GROUND

ICE FLAPPER

SOLENOID

+5V

EVAPORATOR

FAN

DAMPER

MOTOR

VCC(+12)

COM

VCC

COMPRESSOR

CONDENSER

FAN

STANDARD

COMPRESSOR

COMMON

HIGH

LINE

AMBIENT

NTC

DEFROST SENSE

LINE

G5LE RELAY

LIN E

NEUTRAL

AUGER

MOTOR

LINE

CUBE/CRUSHED

ICE GATE CONTROL

DOOR

SWITCH

NEUTRAL

LINE

J3-16

J3-3

J3- 7

DISPENSER VALVE

PRIMARY VALVE

ICE MAKER

FILL VALV E

ICE MAKER FILL SWITCH

G8P RELAY

J4-B1-6

J4-B1-1

J4-B1-2

J4-B1-3

J4-A1-9

J4-A1-3

J4-A1-10

J4-A1-4

J4-A1-11

J4-A1-5

J2- 1

J3- 2

J3-1

J2-2

J1-4

J4-B1-4

J4-A1-6

J4-A1-7

J4-B1-5

J4-A1-13

J4-A1-14

J8- 5

J8- 6

J8- 7

J8- 8

JF- 1

JF- 2

JF- 3

JF- 4

ASSY_OUT

ASSY_IN

+5V

GROUND

+5V

RESET_FLASH

BKGD/MSJ

GROUND

J9A-1

J9A-2

J9A-3

VEE (+12V)

COMM

GROUND

ISOLATED

USER

INTERFACE

J1-1

J2-9

J2-10

J3-13

J3-14

J3-15

J3-16

J1-3

J2-7

NEUTRAL (SERVICE CORD)

NEUTRAL (CONDENSER FAN)

NEUTRAL (WATER VALVE 1)

NEUTRAL (NOT USED)

NEUTRAL (COMPRESSOR)

NEUTRAL (LED POWER SUPPLY)

NEUTRAL (DISPENSER & ICE MAKER VALVE)

LINE (SERVICE CORD )

LINE (Vcc COMPRESSOR)

J6 -1

J6-2

J6-3

J6-4

J6-5

J6-6

J6-7

J6-8

ICE MAKER FAN POWER

TWIST TRAY MOTOR DIRECTION 1

TWIST TRAY SWITCH

NTC POWER

ICE MAKER FAN GROUND

TWIST TRAY MOTOR DIRECTION 2

TWIST TRAY SWITCH

NTC FEEBACK

TWIST

ICE MAKER

ICE & WATER

DISPENSER

CONTROL

OPTIONAL

LED POWER

BOARD

J3- 1

J3- 4

J3- 3

NEUTRAL

FREEZER

LIGHT S

REFRIGERATOR

LIGHTS

FZR DOOR SW. SENSE

J3-9

J3-10

J2-12

J3-8

J3-11

J2-6

LINE

FF DOOR SW. SENSE

Error Codes Special Modes

Display

Interpretation Mode

Display Activate/Deactivate

(press for up to 10 sec.

simultaneously)

FZ FF FZ FF

-- OP- Open FF mid-level

thermistor

Manual

Defrost

d F + and -/same to deac-

tivate

-- OP¯ Open FF upper-level

thermistor

Display/

Showroom

77 77 ^ and -/set

OP -- Open FZ thermistor Sabbath Sb Sb V and +/same to deac-

tivate

-- SH-

Shorted FF mid-level

thermistor

Diagnostic No FF or FZ display,

all UI LEDs on.

^ and V/+ to deactivate

-- SH¯ Shorted FF upper-level

thermistor

Notes:

• Always check for pin back-outs, pinched or damaged wires

before replacing components.

• Determine whether failure is caused by the component, main

control board or wiring. Contact TID before replacing main

control board.

• Refer to Service Manual for additional information.

SH -- Shorted FZ thermistor

SY CF

UI to Main Control Board

communication failure;

on start up

SY CE UI Main Control Board

communication error;

after a period in operation

SY EF Evaporator fan failure

INCANDESCENT LIGHTING MODELS ONLY

FF DOOR SW. SENSE

REFRIGERATOR LIGHTS

FZR DOOR SW. SENSE

FREEZER LIGHTS

NEUTRAL

1 2

Summary of Contents

Page 1 - SERVICE DATA SHEET

SERVICE DATA SHEET242288300ICE & WATER - AUTOMATIC DEFROSTSIDE BY SIDE - R134a IMPORTANT SAFETY NOTEThe information provided herein is designed to

Page 2 - ICE MAKER INFORMATION

242288401VARIABLE SPEED CONTROL BOXVARIABLE SPEED COMPRESSOR(N) WHITELT. BLU(L) PURBLKGRN/YEL5V+ BLK5V- RE DBLK/WHTRED/BLKP.T.C. STARTER WITH RUN CAPA

Frigidaire FPHS2699PF User Manual Page 1

Browse online or download User Manual for Kitchen Frigidaire FPHS2699PF. FRIGIDAIRE FPHS2699PF User Manual

Summary of Contents

More documents for Kitchen Frigidaire FPHS2699PF

Comments to this Manuals

Frigidaire FPHS2699PF User Manual Page 1

Browse online or download User Manual for Kitchen Frigidaire FPHS2699PF. FRIGIDAIRE FPHS2699PF User Manual

Summary of Contents

More documents for Kitchen Frigidaire FPHS2699PF

Comments to this Manuals

Related products and manuals for Kitchen Frigidaire FPHS2699PF