Frigidaire FPHB2899PF User Manual download pdf

SERVICE DATA SHEET

A00606101

ICE & WATER - AUTOMATIC DEFROST

BOTTOM FREEZER - R134a

CAUTION

All electrical parts and wiring must be shielded from torch ﬂame. DO NOT allow

torch to touch insulation; it will char at 200°F and ﬂash ignite (burn) at 500°F.

Excessive heat will distort the plastic liner.

PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT 37°/0°

CONTROL SETTING

Type A with Run / Start Capacitor 65°F (18°C) Ambient 90°F (32°C) Ambient

Operating Time

90 to 100% 100%

Freezer Temperature -5° to 2°F (-20° to -17°C) -1° to 3°F (-18° to -16°C)

Refrigerator Temperature 34° to 39°F (1° to 4°C) 34° to 39°F (1° to 4°C)

Low Side Pressure -2 to 6 psig ( -14 to 41 kPa) -2 to 6 psig (-14 to 41 kPa)

High Side Pressure (last 1/3 cycle) 85 to 105 psig (586 to 724 kPa) 120 to 135 psig (827 to 931 kPa)

Wattage (last 1/3 cycle) 30 to 50 50 to 70

Amps (running)

.4 to .8 .7 to .9

Base Voltage 115 vac (127 vac max)

DEFROST SPECIFICATIONS

Cabinet Size

Thermostat Heater

Cut-in Cut-out Watts Ohms

26’ & 28’ SD, 23’ CD 25°F (-4°C) 47°F (8°C) 500 26.5

Electronic Timer - (ADC) Defrost 24 minutes every 6-96 hours of compressor run time.

CONDENSER FAN MOTOR

Watts RPM Amps

3.1 1100 CW Opposite Shaft 0.03 Running

FREEZER ICE MAKER SPECIFICATIONS

Electrical 115 vac (127 vac max)

Thermostat Opens at 48°F ( 9°C), Closes at 15° F ( -9°C)

Heater Voltage 115 vac

FREEZER ICE MAKER CONNECTOR PLUG CONNECTIONS

Wire Number Wire Color Connects to:

1 Green / Yellow Ground

2 Yellow Water Valve

3 Black Line

4 Light Blue Neutral

IMPORTANT SAFETY NOTE

The information provided herein is designed to assist qualiﬁed repair personnel only. Untrained persons should not

attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance.

IMPORTANT

If any green grounding wires are removed during servicing, they must be returned to their original position and

properly secured.

System Diagnostic Mode

Activate:

Press freezer + and fresh food + for up to 10 sec. simultaneously.

Deactivate:

Press fresh food + for up to 10 sec. Diagnostic Mode will automatically deactivate after 5 min. of inactivity.

Note: Silence alarm.

• Tests marked with “*” may not be applicable to this unit and will not be displayed in System Diagnostic Mode.

• Tests displayed in diagnostic mode but not described below are for internal purposes only; advance through.

• View UI display for “on,” “off,” “CL,” “OP,” “SH,” “LO,” “HI” or numerical results of tests.

• Listen for operating sounds; feel for heat or air ow as appropriate to determine results of tests.

Test To activate test: Passing result

-- First Screen -- All LED lights on UI illuminated

-- Second Screen -- All segments on UI temperature displays illuminated

-- Third Screen -- Blank UI display, no lights illuminated, no shadowing; “-” and “+” blinking on

FF display side to show location.

28 Dispenser Paddle Press disp. paddle “on” on UI when depressed; “off” when released

1* Standard

Compressor

Press set Compressor running when “on”; stopped when “off”

2 Defrost Heater Press set Defrost limit switch must be closed; verify “CL” in test 26.

Feel for heat from defrost heater when “on”.

If “OP” in test 26, heater will not activate.

3 FF Light Press set With FF door open, FF lights on when “on”; off when “off”

8 Water Valve

(Dispenser)

Press set

Be prepared to collect water at dispenser.

Water dispenses when “on”; stops when “off”

9 FZ Light Press set With FZ door open, FZ lights on when “on”, off when “off”

10 Auger Motor Press set FF door must be closed.

Motor running when “on”; motor stopped when “off”

11 Cube/Crush

Solenoid

Press set FF door must be closed. Do not leave solenoid in activated state.

Solenoid activated when “on”; deactivated when “off”

41* Perfect Temp Drawer

(PTD)

Press set PTD UI illuminated when “on”, off when “off”

12* VCC Condenser Fan Press set Fan running when “on”; stopped when “off”

38* VCC Compressor Press set Compressor running when “on”; stopped when “off”

15 Evaporator Fan Press set Fan running for minimum of 10 sec. when “LO” or “HI”; stopped when

“off”. Feedback failure if fan starts but runs less than 10 sec. Listen for speed

change from “LO” to “HI”.

36 Ice Chute Door Depress ice chute door

or press set

“OP” on UI when manually opened; “CL” when closed. Or, using “set,””OP”

on UI when fully opened or “CL” when fully closed by the motor.

22 Damper Press set With inspection mirror, observe damper open when “OP”; closed when “CL”

23 FF Door Open/close FF door “CL” on UI when door closed; “OP” when open

24 FZ Door Open/close FZ door “CL” on UI when door closed; “OP” when open

26 Defrost Limit Switch Activates automatically “CL” on UI when closed; “OP” when open

29 FF Thermistor Mid-

level

Activates automatically UI shows temperature sensed by FF thermistor; pass if within 10°F of tem-

perature measured with gauge at mid-level FF thermistor location.

“OP-” if open; “SH-” if short

30 FZ Thermistor Activates automatically UI shows temperature sensed by FZ thermistor; pass if within 10°F of temperature

measured with gage at FZ thermistor location.

“OP” if open; “SH” if short

33 Ambient Thermistor

@ Main Board

Activates automatically UI shows temperature sensed at main board; pass if within +20°F/-10°F of

temperature measured with gauge at main board location.

“OP” if open; “SH” if short

35* FF Thermistor

Upper-Level

Activates automatically UI shows temperature sensed by upper level FF thermistor; pass if within 10°F

of temperature measured with gauge at upper-level FF thermistor location.

“OP¯” if open; “SH¯” if short

34* Ambient Thermistor

@ UI

Activates automatically UI shows temperature sensed at UI; pass if within +20°F/-10°F of tempera-

ture measured with gauge at UI location. “OP” if open; “SH” if short

46 Humidity Sensor Activates automatically “OP” if open, “SH” if short

AC Heater System: Displays %RH

DC Heater System: “HI” – heater should be on

“Lo” – heater should be off

%RH is displayed when humidity is between “Lo” and “HI” values; heater

could be on or off.

47* Dispenser

Pocket Heater

Press set AC Heater System: “--” ; test not available

DC Heater System: heater on when “on”, off when “off”

0- Firmware

Parameters

Press set Displays digit sequence; record

2- Main Board

Firmware

Press set Displays digit sequence; record

4- UI Firmware Press set Displays digit sequence; record

Variable Capacity Compressor (VCC) Diagnostics (select models)

If test 38 fails, diagnose as follows:

Replace Inverter Board

→ Check at Inverter Board on

Compressor

(BLK and RED wires)

Is Inverter Board receiving 10-15

VAC and 1-5 VDC from Main

Control Board?

→ Check at Main Control Board

(BLK/WHT and RED/BLK wires)

Is Main Control Board sending

10-15 VAC and 1-5 VDC to

Inverter Board?

→ Check at the connector from the power cord

harness into the inverter board, located in

the machine compartment.

(PUR and WHT wires)

Is Inverter Board receiving 115 VAC

from power supply?

• Check voltage supply.

• Check and repair power

cord harness wiring and

connections.

Identify and repair damaged wires or

poor connections between Main Control

Board and Inverter Board.

yes

→ Remove inverter box from the

compressor and check resistance

across compressor winding pairs as

shown.

Is resistance across all winding

pairs equal?

Replace Compressor and

Inverter Board.

→ Check connections from Inverter

Board to Compressor

Are connections from Inverter

Board to Compressor intact?

yes

Identify and repair damaged

wires or poor connections

between Inverter Board and

Compressor.

VCC Resistance Check

Check resistance between terminals 1 and

2, 2 and 3, 3 and 1.

If all resistances are equal,

compressor is operative.

Replace Main Control Board.

yes yes

yes

Error Codes Special Modes

Display

Interpretation Mode

Display Activate/Deactivate

(press for up to 10 sec. simultaneously)

FZ FF FZ FF

-- OP Open FF Thermistor Manual Defrost d F + and - / same to deactivate

OP -- Open FZ Thermistor Display / Showroom 77 77 ٨ and - / Power-on-Reset (POR)

-- SH Shorted FF Thermistor Sabbath Sb Sb ٧ and + / same to deactivate

SH --

Shorted FZ Thermistor System Diagnostic No FF or FZ display, all

UI LEDs on.

٨ and ٧/ + to deactivate

SY CF

UI to Main Control

Board communication

failure; on start up

FFIM Diagnostic Numerical display of

ﬁrst test

٨ and + together to activate /

press and hold + to deactivate

SY CE

UI Main Control Board

communication error; after

a period in operation

Notes:

• Always check for pin back-outs, pinched or damaged wires before replacing components.

• Determine whether failure is caused by the component, main control board or wiring.

Contact TID before replacing main control board.

• Refer to Service Manual for additional information.

SY EF Evaporator Fan Failure

Fresh Food Ice Maker Diagnostic Mode

Activate: Press freezer + and fresh food + temperature pads for up to 10 sec. simultaneously.

Press + or - to move forward or backward through tests.

Deactivate: Press fresh food + for up to 10 sec. FFIM Diagnostic Mode will automatically deactivate after 5 min. of inactivity.

NOTE: Silence alarm.

Test

To activate test

Passing Result

52C Ice Maker Thermistor Activates

automatically

FZ display shows temperature sensed by Ice Maker Thermistor.

“OP” if open; “SH” if short

55C Water Valve Set Remove ice tray to collect water into a measuring container to measure water

ﬁll. If collecting water into ice tray, ﬁrst perform test 63C to empty ice tray.

57C Evaporator Fan (FFIM) Set “On” on FZ display when fan activated, “OFF” when deactivated.

58C

Ice Level Sensor Activates

automatically

Remove ice bucket.

Allow bail arm to drop freely. Pass if no alarm when tray returns to “home” position.

Hold bail arm up. Pass if alarm sounds when tray returns to “home” position.

This test runs continuously until another test is selected.

63C Twist Tray Set Remove ice bucket.

FZ display shows “1” and “GOOD”.

IMPORTANT: PLEASE RETURN THIS SHEET TO ITS ORIGINAL LOCATION.

FREEZER ICE MAKER INFORMATION

(Where Applicable)

Test Cycling: Remove cover by inserting screwdriver in notch at bottom and prying cover from housing. Use

screwdriver to rotate motor gear counterclockwise until holding switch circuit is completed. All components of

ice maker should function to complete the cycle.

Water Fill Volume: The water ﬁll adjustment screw will change the ﬁll time. One full turn is equal to 20cc (.68 oz.).

The correct ﬁll is 102 to 130cc (3.4 to 4.3 oz.). When a water valve is replaced, the ﬁll volume must be checked.

Mounting

Plate

Screws

Mounting

Plate

Screw

Motor

Gear

Timing

Gear

Water Fill

Adjustment

1 2

Summary of Contents

Page 1 - IMPORTANT SAFETY NOTE

SERVICE DATA SHEETA00606101ICE & WATER - AUTOMATIC DEFROSTBOTTOM FREEZER - R134a CAUTIONAll electrical parts and wiring must be shielded from to

Page 2 - Wire Diagram 242292601

Wire Diagram 242292601

Frigidaire FPHB2899PF User Manual

Browse online or download User Manual for Kitchen Frigidaire FPHB2899PF. FRIGIDAIRE FPHB2899PF User Manual

Summary of Contents

Related models: FPHF2399PF

More documents for Kitchen Frigidaire FPHB2899PF

Comments to this Manuals

Frigidaire FPHB2899PF User Manual

Browse online or download User Manual for Kitchen Frigidaire FPHB2899PF. FRIGIDAIRE FPHB2899PF User Manual

Summary of Contents

Related models: FPHF2399PF

More documents for Kitchen Frigidaire FPHB2899PF

Comments to this Manuals

Related products and manuals for Kitchen Frigidaire FPHB2899PF