Frigidaire FGFU19F6QF Specifications Sheet download pdf (Page 3)

Specifications

subject to change.

USA

•

10200 David Taylor Drive

•

Charlotte, NC 28262

•

1-800-FRIGIDAIRE

•

frigidaire.com

CANADA

•

5855 Terry Fox Way

•

Mississauga, ON L5V 3E4

•

1-800-265-8352

•

frigidaire.ca

FGFU19F6QF 18.6 Cu. Ft.

All Freezer

All Freezer (18.6 Cu. Ft.) with ice maker

Professional

Louvered Grille

(for 79"

opening)

(Single Trim Kit shown.)

Cut off

4" for 75"

opening

Top Trim Piece

(for 75"

opening)

Trim Kit

Reversible Kickplate

Leveling System

(2) per unit raises height 2-9/16" min.

Only available with trim kits.

*Minimum depth from face of cabinet side panels

and requires recessed electrical outlet.

Built-In Installation

(without Trim Kit)

Single Unit

(A) 72" (B) 33" (C) 25

/4" min.*

Double Unit (Side-by-Side)

(A) 72" (B) 66" (C) 25

/4" min.*

Built-In Installation

(with Trim Kit & Leveling System)

Single Unit

(A) 75" or 79" (B) 33" (C) 25

/4" min.*

Double Unit (Side-by-Side)

(A) 75" or 79" (B) 66" (C) 25

/4" min.*

All-Freezer

Cutout

Dimensions

Optional Trim Kits

& Dimensions

Kits include top and side trim

pieces, louvered grille, reversible

kickplate and leveling system

to fit 75" or 79" opening height.

Single

Louvered Trim Kit

# TRIMKITEZ1

(D) 75

/8" or 79

/8" (E) 34

/4"

Double

Louvered Trim Kit

# TRIMKITEZ2

(Includes hardware to secure

side-by-side units together.)

(D) 75

/8" or 79

/8" (E) 67

/8"

Note: Both kits attach

directly to cabinetry through

top trim piece or louvered

grille to stabilize unit(s).

Refer to detailed kit installation

instructions packed with

kit or on web.

Allow at

least 57

/4" with door in

90° open position

/8"

/4"

29" to handle

extension

Power

cord

location

(right

bottom

rear)

/8"

/2"

32"

Wat

er inlet location (left bottom rear)

and ice maker connection

location (left top rear)

Recessed electrical outlet

25"

Countertop

24"

Cabinet

/4"

min. side panels,

/2" min. width

(Trim Kit installation requires

/4"

min. width)

Recessed water line

•

Freezer must be placed on level surface of hard material, same height

as flooring. Surface must support approximately 800 lbs. when fully

loaded. Unit equipped with 4-point leveling.

“Built-In Look” Specifications

•

Minimum opening of 72" H x 33" W x 25-1/4" D required for single-

unit “Built-In Look” installation; 66" W required for double-unit

installation. (72" H to be measured from finished floor to underside

of soffit or overhead cabinet.)

•

Remove all wall / floor molding prior to built-in installation.

Optional Trim Kit Specifications

•

If optional Single or Double Louvered Trim Kit is to be used, different

cutout dimensions are required. Kit can be adapted to fit either 75"

or 79" opening height. (Refer to cutout dimensions on this page and

detailed Louvered Trim Kit installation instructions included with kit or

on web.)

•

Remove all wall / floor molding prior to built-in installation.

Note: For planning purposes only. Refer to Product Installation Guide

on the web at frigidaire.com for detailed instructions.

Optional Accessories

•

Single Louvered Trim Kit – (PN # TRIMKITEZ1).

•

Double Louvered Trim Kit – (PN # TRIMKITEZ2).

Built-In All-Freezer Specifications

•

Product Shipping Weight – 255 Lbs.

•

An electrical supply with grounded three-prong receptacle is required.

The power supply circuit must be installed in accordance with current

edition of National Electrical Code (NFPA 70) and local codes &

ordinances.

•

Voltage Rating – 115V / 60 Hz / 20 Amps

•

Connected Load (kW Rating) @ 115 Volts = 0.55 kW

•

Amps @ 115 Volts = 5 Amps

•

Always consult local and national electric & plumbing codes.

•

Water line for ice maker can enter opening through floor or rear wall

Copper tubing recommended between cold water line and water

connection location. Water line tubing recommended is 48" minimum

length by 1/4" diameter. Installation of easily accessible shutoff valve in

water line required.

•

Minimum 25-1/4" depth requires recessed electrical outlet and copper

water line.

•

To allow for ease of installation, tape excess power cord to back of unit.

•

To allow for ease of moving out side-by-side units after installation, 84"

minimum length of coiled copper tubing recommended.

•

When installing freezer adjacent to wall, cabinet or other appliance

that extends beyond front edge of unit, 20" minimum clearance

recommended to allow for optimum 140° door swing, providing

complete drawer / crisper access and removal. (Absolute 4" minimum

clearance will ONLY allow for 90° door swing which will provide limited

drawer / crisper access with restricted removal.)

1 2 3 4

Comments to this Manuals

No comments

Frigidaire FGFU19F6QF Specifications Sheet Page 3

Comments to this Manuals

Related products and manuals for Unknown Frigidaire FGFU19F6QF