Frigidaire 318201613 User Manual download pdf (Page 4)

30" ELECTRIC DROP-IN RANGE INSTALLATION INSTRUCTIONS

1. Electrical Requirements

This appliance must be supplied with the proper voltage

and frequency, and connected to an individual, properly

grounded branch circuit, protected by a circuit breaker or

fuse 40A or 50A.

Observe all governing codes and local ordinances

1. A 3-wire or 4-wire single phase 120/240 or 120/208

Volt, 60 Hz AC only electrical supply is required on a

separate circuit fused on both sides of the line (red

and black wires). A time-delay fuse or circuit breaker is

recommended. DO NOT fuse neutral (white wire).

NOTE: Wire sizes and connections must conform with

the fuse size and rating of the appliance in accordance

with the American National Electrical Code ANSI/NFPA

No. 70-latest edition, or with Canadian CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local codes

and ordinances.

An extension cord should not be used

with this appliance. Such use may result in a ﬁre,

electrical shock, or other personal injury. If you need

a longer power cord you can purchase a 10' (3 m) power

cord kit #903056-9010 by calling the Service Center.

2. These appliances should be connected to the fused

disconnect (or circuit breaker) box through ﬂexible

armored or nonmetallic sheathed cable. The ﬂexible

armored cable extending from the appliance should

be connected directly to the junction box. The

junction box should be located as shown in Figure

1 or Figure 2 and with as much slack as possible

remaining in the cable between the box and the

appliance, so it can be moved if servicing is ever

necessary.

3. A suitable strain relief must be provided to attach

the ﬂexible armored cable to the junction box.

In cold weather shipping and storage

conditions, make sure that oven is in ﬁnal location

at least three (3) hours before switching on power.

Switching on power while oven is still cold may damage

the oven controls.

2. Electrical connection

It is the responsibility and obligation of the consumer to

contact a qualiﬁed installer to assure that the electrical

installation is adequate and is in conformance with the

National Electrical Code ANSI/NFPA No. 70-latest edition,

or with CSA Standard C22.1, Canadian Electrical Code,

Part 1, and local codes and ordinances.

Risk of electrical shock (Failure to

heed this warning may result in electrocution or

other serious injury.) This appliance is equipped

with copper lead wire. If connection is made to

aluminum house wiring, use only connectors that

are approved for joining copper and aluminum wire

in accordance with the National Electrical Code

and local code and ordinances. When installing

connectors having screws which bear directly on

the steel and/or aluminum ﬂexible conduit, do no

tighten screws sufﬁciently to damage the ﬂexible

conduit. Do not over bend or excessively distort

ﬂexible conduit to avoid separation of convolutions

en exposure of internal wires.

DO NOT ground to a gas supply pipe. DO NOT connect

to electrical power supply until appliance is permanently

grounded. Connect the ground wire before turning on

the power.

Electrical Shock Hazard

•Electricalgroundisrequiredonthisappliance.

•Donotconnecttotheelectricalsupplyuntil

applianceispermanentlygrounded.

•Disconnectpowertothejunctionboxbefore

makingtheelectricalconnection.

•Thisappliancemustbeconnectedtoa

grounded,metallic,permanentwiringsystem,

oragroundingconnectorshouldbeconnected

tothegroundingterminalorwireleadonthe

appliance.

•Donotuseagassupplylineforgroundingthe

appliance.

Failuretodoanyoftheabovecouldresultina

re,personalinjuryorelectricalshock.

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Frigidaire 318201613 User Manual Page 4

Comments to this Manuals

Related products and manuals for Radio Frigidaire 318201613